Shop headings: New Spares | Used Spares | Accessories | Brands
CEV type lights (off/pilot/on), main beam and horn switch. Supplied without wires, you will need to solder your wiring into the switchgear using a minimum 60W soldering iron. Switch fixes to handlebars using included screws
Can be fitted to left or right side of bars
This part is due back in stock soon, call 01484 841395 to reserve yours
12746001-z 12746001 GU12746001 12 74 60 01
1274 6001 1274.6001 12.74.60.01
£60.00
INC VAT
£50.00 EX VAT
Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.
Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear
This part is due back in stock soon, call 01484 841395 to reserve yours
01738030 GU01738030 01 73 80 30
0173 8030 0173.8030 01.73.80.30
£88.00
INC VAT
£73.33 EX VAT
Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501
On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.
This part is due back in stock soon, call 01484 841395 to reserve yours
01738800 GU01738800 01 73 88 00
0173 8800 0173.8800 01.73.88.00
£51.00
INC VAT
£42.50 EX VAT
Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils
Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit
This part is due back in stock soon, call 01484 841395 to reserve yours
£28.00
INC VAT
£23.33 EX VAT
Push button starter switch, chrome finish body, screw contacts to rear
This part is available by special order, request a quote
26735001-z 26735001 GU26735001 26 73 50 01
2673 5001 2673.5001 26.73.50.01
£19.80
INC VAT
£16.50 EX VAT
12 volt single output 3 Ohm ignition coil (lead to distributor)
Push fit HT lead, see ELA00001 for crimp on HT lead connector. Supplied without coil clamp
This part is due back in stock soon, call 01484 841395 to reserve yours
26716504 GU26716504 26 71 65 04
2671 6504 2671.6504 26.71.65.04
£58.00
INC VAT
£48.33 EX VAT
Silca key blank for ignition key, match profile to your existing key
This part is due back in stock soon, call 01484 841395 to reserve yours
NE5
£4.20
INC VAT
£3.50 EX VAT
Silca key blank for ignition key, match profile to your existing key
This part is due back in stock soon, call 01484 841395 to reserve yours
£4.20
INC VAT
£3.50 EX VAT
Complete gasket kit, including exhaust and inlet gaskets
Does not include rubber seals
This part is due back in stock soon, call 01484 841395 to reserve yours
£65.00
INC VAT
£54.17 EX VAT
Rocker cover gasket
This part is due back in stock soon, call 01484 841395 to reserve yours
10024700-z 10024700 GU10024700 10 02 47 00
1002 4700 1002.4700 10.02.47.00
£4.00
INC VAT
£3.33 EX VAT